A bundle of medical extrusions on a steel bench: multi-lumen, braided, coil-reinforced, micro-bore and striped tubing

Precision
medical
extrusion.

Engineered tubing for devices that cannot afford compromise.

Discuss your extrusion project ISO 13485 · FDA listed · ISO Class 7 & 8

The architecture
of precision.

Standard tubing is a commodity. Your device needs an engineered component.

Geometry. Material. Mechanics.

All three must work together.

  • Tolerance
  • Lumen architecture
  • Kink resistance
  • Pushability
  • Visibility

External geometries

Beyond
the circle.

Non-round and kink-resistant profiles, validated on our own tooling.

A cluster of blue, white and clear extruded tubing in round, multi-lumen and shaped profiles
Five translucent multi-lumen tubes showing different internal lumen layouts in cross-section

Lumen anatomy

Isolation,
by design.

Slot
Crescent
D-shape
Oval

Electrical, fluidic and mechanical pathways, separated inside one outer diameter.

>95%Concentricity.
Uniform walls, predictable pressure ratings.

A clear multi-lumen extrusion with a ring of small lumens around a central bore

12Functional channels.
One extrusion.

  • Guidewires
  • Pull-wires
  • Fluids
  • Sensors

Melt pressure and pull speed, synchronised. No collapsed or merged lumens.

Illustrative cross-section with twelve lumens: one central channel and eleven around it
Illustrative cross-section

Micro‑bore.
Macro control.

Internal diameters of 1.0 mm and below. Tolerance to ±0.025 mm. Built for neurovascular and ophthalmic devices.

Two printed micro-bore dual-lumen tubes marked 1.3 mm / 4 Fr beside a pencil for scale

Precision in
every layer.

2 to 5+ discrete layers in one pass: a PTFE liner for lubricity, tie layers for bonding, an outer jacket for durability. Tri-layer barrier walls for fluid management and drainage.

Fluoroscopy image showing a radiopaque catheter clearly visible along the spine

Radiopaque engineering

Seen when
it matters.

Radiopaque compounds and longitudinal striping for fluoroscopic visibility.

Barium sulfate · Bismuth · Tungsten, loaded up to 90% by weight. Tungsten attenuates at a lower volume fraction, so the wall keeps its elasticity and tear strength. Multi-stripe and colour-coded lines available.

Two coil-reinforced tubing shafts curved on a white surface

Structural reinforcement

Soft outside.
Strong within.

Cutaway of a reinforced shaft: etched PTFE liner, metallic coil, thermoplastic jacket and FEP heat shrink 4 3 2 1
  1. 1Etched PTFE liner
  2. 2Metallic coil
  3. 3Thermoplastic jacket
  4. 4FEP heat shrink
Thermal reflow fuses jacket, coil and liner into one integrated shaft.

Stainless steel or MRI-compatible polymer coils. Cross-head overjacketing. Multi-durometer shafts, rigid proximal to flexible distal.

Discuss your extrusion project

Secondary operations

The critical
last mile.

Extrusion is the beginning. The finish defines the device.

Three catheter tips: a curved Tieman tip, a closed Nelaton tip with side eye, and an open tapered tip

01 · Atraumatic tip forming

Form.

No sharp edges. Nelaton, Tieman, Olive, Tapered, bevel, closed and round-ended profiles.

Two white shafts each joined to a soft blue distal tip

02 · Variable stiffness & dual-hardness

Join.

Stiff proximal end for pushability. Ultra-soft distal tip for delicate anatomy.

Clear tubing with precision-punched apertures in different shapes, held on a fixture

03 · Precision hole punching

Punch.

Automated apertures with zero internal or external debris. No burrs, no particulates.

Corona treatment head discharging over a row of tubes

04 · Corona surface pre-treatment

Treat.

Depth markers, QR codes and logos, permanently bonded, even on PTFE.

Orange tubing with laser-marked depth markers at 35 and 40

05 · Laser marking

Mark.

Depth markers, QR codes, and logos, permanently marked, safe for patient use.

CCB stainless-steel ultrasonic cleaning tank

06 · Validated ultrasonic cleaning

Clean.

Deep inside the micro-lumen. Every lot recorded in a Device History Record.

Design. Validate.
Produce.

Concept, tooling and manufacturing under one roof.

  1. 01RequirementYour design input
  2. 02EngineeringMaterial and profile
  3. 03ToolingPins and dies, in-house
  4. 04PrototypeProven for mass production
  5. 05OptimisationReal-time OD/ID laser control
  6. 06ValidationFull IQ/OQ/PQ
  7. 07Production24/7, ISO Class 7 & 8
  8. 08Secondary opsFinished, cleaned, recorded

Specification summary

Medical extrusion at a glance.

CCB Medical is a medical device contract manufacturer in Penang, Malaysia, that engineers and produces precision medical extrusion for device makers worldwide.

Multi-lumen
CCB produces multi-lumen medical extrusion with up to 12 functional channels, in slot, crescent, D-shape and oval lumen profiles.
Micro-bore
Internal diameters of 1.0 mm and below, with dimensional tolerances as tight as ±0.025 mm.
Concentricity
Concentricity ratios above 95% for uniform wall strength and pressure ratings.
Multi-layer
2 to 5+ discrete layers combined in a single co-extrusion pass.
Radiopaque
Barium sulfate, bismuth or tungsten compounds loaded up to 90% by weight, plus radiopaque and colour-coded striping.
Reinforced shafts
Stainless steel or MRI-compatible polymer coils, cross-head overjacketing and thermal reflow lamination.
Secondary operations
Atraumatic tip forming, dual-hardness joining, precision hole punching, corona pre-treatment and validated ultrasonic cleaning.
Quality
ISO 13485:2016 certified, US FDA listed and EU MDR compliant. Full IQ/OQ/PQ validation, ISO Class 7 & 8 cleanrooms operating 24/7, and Device History Record traceability.
Location
Penang, Malaysia. Founded in 2005; a Malaysian–German joint venture with VBM Medizintechnik GmbH since 2017.

Engineering confidence

Can you trust
CCB with your device?

Medical devices in Penang since 2005. A Malaysian–German joint venture with VBM Medizintechnik GmbH since 2017.

ISO 13485:2016
Certified. US FDA listed, EU MDR compliant.
Cleanroom manufacturing
ISO Class 7 & 8, operating 24/7, across about 80,000 sq ft.
Validation
Full IQ/OQ/PQ with documentation for regulatory submission.
Traceability
Device History Record for 100% traceability.
Engineering support
Engineer to engineer, with IP protection and full transparency.
CCB technicians assembling medical devices in the Penang cleanroom
CCB cleanroom, Penang, Malaysia. Customers across Europe, the U.S., the Middle East and Asia Pacific.

Technical FAQ

Can CCB manufacture multi-lumen medical tubing?

Yes. CCB produces multi-lumen medical extrusion with up to 12 functional channels. Lumens can be slot, crescent, D-shape or oval, and melt pressure and pull speed are synchronised so each lumen keeps its geometry without collapsing or merging.

How small can CCB medical extrusion be?

CCB produces micro-bore tubing with internal diameters of 1.0 mm and below, holding dimensional tolerances as tight as ±0.025 mm through die swell management. This suits neurovascular and ophthalmic applications.

Can CCB produce custom non-round extrusion profiles?

Yes. Custom external shapes, including non-round and kink-resistant geometries, are validated on CCB’s in-house tooling so the design output matches your design input.

Can CCB support multi-layer co-extrusion?

Yes. CCB supports 2 to 5+ layer co-extrusion in a single pass, for example a PTFE liner for lubricity, a tie layer for bonding and an outer jacket for durability. Tri-layer barrier constructions are available for fluid management and drainage.

Can CCB produce radiopaque medical tubing?

Yes. Host polymers are compounded with barium sulfate, bismuth or elemental tungsten, loaded up to 90% by weight, and radiopaque or colour-coded longitudinal stripes can be integrated into the wall.

Can CCB manufacture reinforced catheter shafts?

Yes. CCB offers stainless steel or MRI-compatible polymer coil reinforcement and cross-head overjacketing. Thermal reflow lamination fuses the polymeric and elastomeric jacket through the coil onto the inner lining layer.

What secondary operations are available?

Atraumatic tip forming (including Nelaton, Tieman, Olive and tapered tips), variable stiffness and dual-hardness joining, precision hole punching, corona surface pre-treatment and validated ultrasonic cleaning, all in-house in ISO Class 7 and 8 cleanrooms.

Can CCB support IQ/OQ/PQ validation?

Yes. CCB works under an ISO 13485:2016 quality system and provides full IQ/OQ/PQ process validation with documentation for regulatory submission. Lines use laser micrometers for real-time OD/ID monitoring, and a Device History Record provides traceability.

Where is CCB Medical Devices located?

In Penang, Malaysia, at PMT 1124, Jalan Perindustrian Bukit Minyak 8, 14100 Simpang Ampat. CCB was founded in 2005 and has been a Malaysian–German joint venture with VBM Medizintechnik GmbH since 2017.

Can we submit drawings or specifications for engineering review?

Yes. Send a drawing, cross-section, material requirement, sample details or performance problem through the enquiry form below, and CCB engineers will review it.

Have a medical
extrusion challenge?

Send a drawing, cross-section, material requirement, sample or performance problem. Our engineers take it from there.

An engineering discussion, not a retail quotation form.